Re: Printing gray

ss <> writes:

> On my black ink it is printing gray, installed a new black ink
> cartridge and have unchecked grayscale. Cartridge is full of ink.

Is this an old thread, or did you not provide any information on your
printer at all? That would be helpful!

Possibilities:

1) if test pattern looks bad, you have blocked nozzles preventing good
coverage. So you should clean the printhead. If the printhead is on
the cartridge, this will not apply to a new cartridge.

1) if black looks gray, you could be using a really low-quality draft
mode, which always looks gray rather than black. Try a higher
quality.

3) you could be using composite black instead of real black, which
again looks gray since it is made up of CMY color.
--
Gernot Hassenpflug

On 8/06/2012 10:11 PM, ss wrote:
> On 08/06/2012 08:06, ss wrote:
>> On 08/06/2012 04:38, Gernot Hassenpflug wrote:
>>> ss<> writes:
>>>
>>>> On my black ink it is printing gray, installed a new black ink
>>>> cartridge and have unchecked grayscale. Cartridge is full of ink.
>>>
>>> Is this an old thread, or did you not provide any information on your
>>> printer at all? That would be helpful!
>>>
>>> Possibilities:
>>>
>>> 1) if test pattern looks bad, you have blocked nozzles preventing good
>>> coverage. So you should clean the printhead. If the printhead is on
>>> the cartridge, this will not apply to a new cartridge.
>>>
>>> 1) if black looks gray, you could be using a really low-quality draft
>>> mode, which always looks gray rather than black. Try a higher
>>> quality.
>>>
>>> 3) you could be using composite black instead of real black, which
>>> again looks gray since it is made up of CMY color.
>>
>> Apologies, it is an HP 1317 all in one printer/scanner.
>> The colour cartridge appears to print ok although it lacks
>> `brightness`when printing colour (maybe not the correct word) due to
>> what appears to be a lack of black ink being used in the production of
>> the picture.
>> The test pattern is ok.
>> The printhead is on the cartridge.
>> I will check your other points.
>
> Update.....
> I got tough with it and gave the print head a good clean with cleaner
> and now printing again, it must have been a blockage. I was on hols for
> 3 weeks and maybe it dried up a little in the `jets`.

Interesting that you could print a test pattern which you say was OK.

Then clean the heads to rectify the problem.

I suggest that you find a decent test chart to check the nozzles.

Even if one nozzle is down on mine it will upset the balance not sure
what pattern HP print I have an Epson printer.

Ill dig some up and post the URL tomorrow.

On 9/06/2012 12:46 AM, ss wrote:
> On 08/06/2012 14:25, Rob wrote:
>> On 8/06/2012 10:11 PM, ss wrote:
>>> On 08/06/2012 08:06, ss wrote:
>>>> On 08/06/2012 04:38, Gernot Hassenpflug wrote:
>>>>> ss<> writes:
>>>>>
>>>>>> On my black ink it is printing gray, installed a new black ink
>>>>>> cartridge and have unchecked grayscale. Cartridge is full of ink.
>>>>>
>>>>> Is this an old thread, or did you not provide any information on your
>>>>> printer at all? That would be helpful!
>>>>>
>>>>> Possibilities:
>>>>>
>>>>> 1) if test pattern looks bad, you have blocked nozzles preventing good
>>>>> coverage. So you should clean the printhead. If the printhead is on
>>>>> the cartridge, this will not apply to a new cartridge.
>>>>>
>>>>> 1) if black looks gray, you could be using a really low-quality draft
>>>>> mode, which always looks gray rather than black. Try a higher
>>>>> quality.
>>>>>
>>>>> 3) you could be using composite black instead of real black, which
>>>>> again looks gray since it is made up of CMY color.
>>>>
>>>> Apologies, it is an HP 1317 all in one printer/scanner.
>>>> The colour cartridge appears to print ok although it lacks
>>>> `brightness`when printing colour (maybe not the correct word) due to
>>>> what appears to be a lack of black ink being used in the production of
>>>> the picture.
>>>> The test pattern is ok.
>>>> The printhead is on the cartridge.
>>>> I will check your other points.
>>>
>>> Update.....
>>> I got tough with it and gave the print head a good clean with cleaner
>>> and now printing again, it must have been a blockage. I was on hols for
>>> 3 weeks and maybe it dried up a little in the `jets`.
>>
>> Interesting that you could print a test pattern which you say was OK.
>>
>> Then clean the heads to rectify the problem.
>>
>> I suggest that you find a decent test chart to check the nozzles.
>>
>> Even if one nozzle is down on mine it will upset the balance not sure
>> what pattern HP print I have an Epson printer.
>>
>> Ill dig some up and post the URL tomorrow.
>
> I was never happy with the test pattern with HP so done my own which
> allows me to see the colours so I could understand them. When I ran this
> the tri colours were fine but the black was gray and there was no
> streaky lines to indicate a `dirty` nozzle. Thats what was confusing me.
> But as mentioned now sorted.
>


http://www.normankoren.com/makingfineprints1A.html