Kyocera FS-C2126 MFP skew/offset problem

Joined
May 14, 2014
Messages
1
Hello, we have a Kyocera FS-C2126 MFP that is shifting all the print/copy images up and chopping off an inch or inch and a quarter from the top. Sometimes there will be a solid black line also on the bottom of the page, about a half an inch. Tried finding the Printer Offset function in Sys/Counter Menu>Printer>Printer Offset, but it isn't there. I ran a drum refresh and MC adjustment, but neither helped. Also the color is way off too.. When printing a color page with RedGreenBlueWhiteMagentaYellowCyanRedGreen The white almost doesn't even come out cause the other colors are shifted into that zone and shifted up/down.... Any suggestions on what I could try?






Color Offset.jpg
 
Joined
Mar 2, 2012
Messages
13
Hello, we have a Kyocera FS-C2126 MFP that is shifting all the print/copy images up and chopping off an inch or inch and a quarter from the top. Sometimes there will be a solid black line also on the bottom of the page, about a half an inch. Tried finding the Printer Offset function in Sys/Counter Menu>Printer>Printer Offset, but it isn't there. I ran a drum refresh and MC adjustment, but neither helped. Also the color is way off too.. When printing a color page with RedGreenBlueWhiteMagentaYellowCyanRedGreen The white almost doesn't even come out cause the other colors are shifted into that zone and shifted up/down.... Any suggestions on what I could try?






View attachment 125

I have a kyocera FS 1010 best printer ive owned had for so many years now I forget when I got it lol any hooo, mine used to start printing half way down the page on the from page, been this way for a couple of years, the other day when looking for stuff for another reason I came across this post, its a gem, if you have a bit of nouce and take your time it takes about an hour and a half to fix . . .

Fixing a faulty Kyocera FS-1010 printer with cardboard and glue
We don't do a lot of printing and since We have become a laptop only household printing has been further discouraged since going to the printer and plugging in is simply too much effort, I just save/print it to a PDF.

So after finally setting my printer as a network printer, using an old laptop, I was dismayed to find that the printer was not printing the first page correctly, the printing would start almost halfway down the page, strangely however subsequent pages of each job were printing just fine.

The printer is a Kyocera FS-1010, laser printer.

After some searching around the web I found a few people reporting the same symptoms:
h t t p://w w w.fixya.com/support/t1083180-huge_margin_kyocera_fs_1000]Huge Margin with Kyocera FS 1000+ - Fixya

But then I came across these threads on copytechnet forums:
h t t p://w w w.copytechnet.com/forums/kyocera/15980-kyocera-fs1010-delayed-printing-1st-page-2.html#post55451

Basically there are some foam pads that insulate some moving arms from their stop point. These get compressed over time and no longer insulate the arms and they get magnetically stuck on the stop points.

The steps from this post are :

Open the right side of the printer

Disconnect all connections to engine board

Remove engine board

Remove plastic guard (white)

remove all 3 solenoids

Replace all pads on the solenoids that come up against stops

Registration Solenoid has 2 pads (1 against the solenoid frame and the other on a stop arm, the others just the frame pad)

Keep thickness to around .4 - .5mm Too thick on register arm will cause early printing.

Reassemble


So with the above and a service manual downloaded from : h t t p://w w w .eserviceinfo.com/downloadsm/16172/Kyocera_FS-1010.html

I was able to open the printer, access the solenoids scrape off the old foam and glue some thin cardboard in their place.

After a successful 'Step 9' Reassemble, printing is back to normal!

There aren't many items in this tech would that can be fixed so easily simply, Of course opening up a printer and removing bits a pieces is not usually regarded as easy.
 

Ask a Question

Want to reply to this thread or ask your own question?

You'll need to choose a username for the site, which only take a couple of moments. After that, you can post your question and our members will help you out.

Ask a Question

Top